Nilight
$23.39 Price may change
30 videos
Nilight TR-05
Nilight 4PCS RGB LED Underglow Lights for Cars with Wireless Remote | 252 LEDs Neon Accent Strip Lights 8 Color Sound Active Function Music Mode Underbody Light Strips for Cars Van SUV Truck
Daniel
Easy install with the 3M adhesive tape, brighter than OEM at a great price. Photos at night would show the difference better, but during the daylight you can still see it lights up the entire bed. This came complete with everything needed, I’ll probably buy a second set for my trailer.
Gabriel Francisco Acosta mielgo
Buena iluminación y fácil de instalar en mi bote
isaac
Would rate it lower but im not %100 sure if its on my end or the company's. The lights are sometimes week at times and randomly gets bright. I probly just dont have a good ground or 12v.
Jozeph
Super easy to install!! Very bright but not completely blinding, they have exceeded my expectations. My truck has a 7ft bed and a tool box and the lights fit perfectly in between the space from the back of the tool box to the tailgate. 3m sticky tape stuck right to my bed liner so you don’t really need the drill in hardware!!!! 10/10. Only thing I used different than what it came with was butt connecting crimps instead of the cap crimps it came with to wire the lights in!
Busybuildr
Light strips are very bright, but the adhesive is trash. I put them up this morning, after thoroughly cleaning the surface,
and 4 hours later, they are already falling down. I'd return them, but I've already cut the length of the strips to fit my application.
I'll have to get a small roll of 3M Extreme tape and replace their adhesive with some better stuff. Not looking forward to peeling and cleaning all of the OEM tape, but it's the best way to proceed.
The adhesive can be removed by pushing / rolling it with your fingers. DO NOT use solvents on the plastic channel !
After cleaning the strip carefully with alcohol, lightly sand the mounting surface (180 grit) to a smooth matte finish.
Re-clean with alcohol, let dry and apply the 3M tape. Rub or roll it down to ensure a good bond.
UPDATE: I have removed the OEM adhesive and replaced it with Scotch Extreme 30 lb test tape. After cutting the LED strips to length, I noticed that there in a hollow tube, not encapsulated. If you cut them, be sure to fill the end of the tube with silicone to re-seal it from moisture (see photo 2).
UPDATE 2: I got these installed and wired up yesterday. The leads on the light strips are plenty long, but the connecting harness, IMHO, is backwards. The short lead on the push button makes it mandatory that the power feed and strip leads meet at the back of the bed ( you'll want the push button near the tailgate). They should all meet in the front of the bed where it's a short distance out of the bed and up to the battery. A much longer lead on the push button could then reach all the way to the back of the bed.
After a little cutting and splicing, I got it done. I spliced the fuse inline at the positive battery connection - you don't need to get under the truck to check the fuse !
Overall, happy with the result, but a lot more work than it needs to be.
Henry
Excelente luz, fácil instalación.
Brian Tasker
Great set of bed lights, came with everything you need to install them. I elected to tap into the factory wiring so that they come on and off with the factory cargo lights up by the third brake light above the rear window. These are nice and bright and I highly recommend them!
Eric
They work, I had a difficult time with the bed rail and the 3M tape on the strip wouldn’t stick to bed. The clips and screws that come with it are crap. But so far it works well light wise, might just have to get some of your own hardware to get it to install.
Luke Wilson
These lights were very easy to install it took me maybe 30 min to an hour they did give me a short wire to go all the way from the back to the front but I’m lucky I work at an electrical company but they are very bright and will be perfect for duck season!!!
Matt
Lights were easy to install. I had to take my bed cover and bed liner out to get a good install. Make sure you clean wherever you are going to place them with alcohol. After unrolling the lights I put something heavy on top of the lights to straighten them out for 30 to 45 mins. They look great, and now I can see the entire bed at night. So far they have been installed for a week and they have not came off the underside of the bed.
Andy Gustafson
Very bright and easy to wire. It would be nice if they gave you better screws for the mounting bracket, but you can always use some self tappers. I wired mine into my cargo light, making it very easy to use.
Tristain
I added my own switch to it but I love the way it came out I would definitely recommend
Nick
Great quality lights. Good adhesive. It stick nicely to the Ryno lined bed. I still put on the provided straps. Wiring was a breeze. I recommend these to all.
Corey B
Wired these up to a separate switch because I wasn’t impressed with the quality of the switch that came with the kit. Even with that I still give these 5 stars simply for the value.
Blue Collar Barista
These lights turned out great. I was skeptical at first because I was afraid of a bluish white tint. However, these lights are a much more whiter hue. As other reviews stated these are very bright. Little tip: I installed these a little up inside the bed rail in an attempt to somewhat hide them. This causes the light to cast a small shadow as seen against the cab. So plan and layout lights accordingly. Also I have a 5 1/2 foot bed and I had to cut off a small section at the end to get a more uniform fit. Overall much happier with these over my previous lights. Definitely worth the price.
Keegan Spell
So, let me start off by saying I absolutely love being able see in my truck bed now. These lights are more than enough in the darkest night. They even light up the tailgate enough for a makeshift workstation.
The reason for only 3 stars is the wiring and the switch.
Wiring: the wiring included was not enough to reach to the battery. Luckily I had more and the connectors, so it didn’t cost me anything extra. Also, the wiring for the switch was not long enough for my application. I had to add more wire to place the switch at the back of the tailgate. Perhaps the way I thought best to install it wasn’t the manufactures intent, but my way seemed to make more sense.
Button: the first rain that came had the button get slightly wet. Not soaking, but just slightly. The inside of the button corroded and rendered the lights nonworking. I had to take it apart and clean the rust before it would work again. I have since bought a weather proof switch that I anticipate will work much better.
All in all, I think it’s a great addition to my truck and I enjoy it, but it wasn’t perfect. If you know basic wiring, you can make this really great.
Trevor Knotts
I have bought numerous Nilight products in the past and have had great luck with their products. These strips were put on June of last year and the passenger side quit working the other day. Only the front half of the white leds would come on and just one amber led that flickered. (As seen in video) . Going with a different brand and see how they work out.
Rich
This product is perfect to light up the bed of your pickup truck. I have the 5’7” short bed full size truck and the light strips fit perfectly on each side. The quality of this product is good and the light covers the complete bed. At night, you can see to the back of the bed easily. I wired mine to the battery so that I can use the provided switch to turn on the lights when needed. If you wire them to the vehicles light system like the bed light, they will time out with the vehicle. This can be annoying when you’re unloading lots of stuff at night. Highly recommend this easy to install product and an affordable price.
jacob knowles
Looks great! Puts out a lot of light, I did get rid of the switch it came with and went to auto zone and picked up a different switch.
Junk
Lights up the whole ground behind ur truck they are so awsome! install was easy , running off a dewalt batteries for now until I have more time to wire it to truck battery. I highly suggest these if you get back from late rides and camp ,working and are a non stop person like me.
Matthew M.
These are nice lights for the truck bed. I cut them shorter and the end cap is removable so you can adjust the length of the protective housing. I wired them up to a push button and a magnetic switch so they come on when the tailgate is open but there’s a manual override button.
Darian G
As you can see from the video I've posted, these lights are very bright at night. It has a convenient off and on push button switch which I will upgrade later. The installation was very, very easy to do. The adhesive tape on the back is very sticky and so far after being in the heat all day, it's holding up. Next I will be purchasing them for the bed of my truck, the 3 PC set.
Matthews fam
Packaged VERY nicely. Each length of lights was rolled and packed in a anti-static bag. Cables are nice and thick and extra wire length is included (20gauge). I unrolled the lights and laid in the sun for a while to get the roll shape out of them.
Installed inside the carpeted topper shell of my Toyota Tundra double cab. The length was perfect for the 5' bed of this truck, and the VHB tape that came on them was plenty strong to attach and grip the carpet. It is not marked 3M but it is doing a great job holding, even in 90 degree+ heat back there! Was concerned and ready to replace with the "good stuff" but don't think I need too.
Pics show how bright the light is even in the daytime, sure the high mount location is going to do a great job lighting up the entire bed at night (did this with work truck and is easy to see everything back there at night now).
Wires simply spliced into the pathetic topper shell factory light. I used a roll of double sided hook and loop (Velcro) from Harbor Freight to cover the wires, (3/4" x 35' roll hook and loop cable strap- $7) I just pressed the rough side of the velcro right to the carpet, sticks great and no residue if I need to remove/repair the wires later. Used the same to hold the bundled wires to to the carpeted ceiling/walls of the shell, (not the cleanest looking job but I'll work on it more later). Nothing else needed to get this system working.
Located the switch inside the glass near the gas strut attachment with some more velcro simply right over the end of the switch on one end and the incoming wire on the other and I'm all set! The switch is a push button with something of a rubber gasket on the button itself, but as the wire only comes into one side of the switch, there is a small hole on the other end that is not filled. If I didn't have a topper shell, I'd definitely do something to "weatherproof" this thing before leaving it out in the exposed truck bed.
Note: These lights are not "sealed" the same way other strip LED lights I've used. Other brands embed the entire LED strip in some sort of clear resin that is pliable. This set has the lights in a hollow casing with caps on either end. They look sealed but I don't think I'd trying submerging them. Not sure this is fully sealed if used in an outdoor location, but since I have it in the protected location I do, I'm not worried myself, just FYI.
Marcellus D. Pierre
The product seems to work like a charm but my only concern is wiring the switch. I wanted to mount the switch towards the tailgate, but due to the pigtails are gonna run towards the cab, I’m having to wing it. Still nice setup and I give it a 5 out of 4 stars ( 1 in 3 people have an issue with simple numbers lol)
Update: I did wire it with the switch on the left side rear of tailgate. It works perfectly & allows for an outdoor light source when in the backyard around the burn pit. Depending on its ability to endure heat, I may wire on under my hood in order to provide extra lighting when working underneath the hood or on the side of the road.
Jaz R.
Super easy to install and the brightness is way brighter than expected! I added a pin switch to mine so when opening and closing the tailgate it turns on/off the lights! So far lights have held up in the Texas heat! Highly recommend!
Nichole King
So far I like what I see ! I just installed them . They are really bright and look good under my 2020 f250 steps . I just hope they stick well and hold up . Very easy to install as well .
O'Carroll Lawncare
I added these lights under my vehicle. They act as the running board lights to provide bright and clear ground light. The video was done at 7 am to give you an idea how bright they are.
Codeman
Installed on a 2019 Chevy Colorado with good results. I like these because they have a switch and are more rigid than other similar products. I recommend laying them out and flattening with a board for a day or so prior to install because they maintain a curl from the packaging. Instructions are simple enough. The adhesive seems really good so I didn’t use the provided brackets/screws. Everything seems to be holding up nicely
I did not connect these to the factory bed light wiring behind the drivers side tail light. This option is nice but would rely on using the cargo Lamp switch to activate. I like the thought but I’m always working in the back and wanted to be able to operate the lights without getting in the cab. I opted to install an external battery in a bracket on the underside of the vehicle and mount the switch to my bed molle panels. I don’t regret it.
The lights cover most of the bed while leaving a dark center strip. Even this strip is much more illuminated than it would have been otherwise. Molle panels interfere a bit but not enough to matter. Overall the lights are a great addition and value.
nycpap
very bright I I attached them to the interior lights so when you open the door the lights will come on didn't think it would be that bright but they are bright under the car if you drop anything you will definitely be able to find it under the car I just ordered a second pair to put under the front and back of the car
J. Medina
I installed these over the weekend - hardest part was having to run a power wire from the battery through the cab, under the bed and up to the rear tail-light. And that wasn't even that hard. Then I mounted the lights to the bottom of my utilitrack rails. Much of the light is aimed downward but there's enough reflection when it's dark out to light up the whole bed plenty. They come with plenty of wire, I had way too much extra on the driver side so I cut a good portion out, and ended up splicing it into the passenger side which was long but still not long enough to reach the driver side where everything is connected. All in all if you have some basic electrical soldering skills you can easily make this work for your needs. Warranty will go out the window but just test everything first and you'll be fine. Time will tell if the adhesive lasts, but make sure you clean with alcohol first. I saved the clips just in case I need to screw them in. I also had to cut a foot off each length. A razor blade pushed straight down at the spot marked for cutting was all it took. Overall, for $20 you can't beat it.
$23.39
View offer