WUPP
$11.98 Price may change
13 videoszack
EVERYONE CHECK YOUR PARASITIC DRAW!
This fuse block is constantly pulling 11.6Volts without fuses! They state (And i did not notice this before i bought it) that a small amount of voltage will be used due to the led lights! that should not cause all 6 of my posts to be 11.6 to 11.7 volts!!!! Will be returning and going with a different company.. That is NOT good. in the photo you can see the LED light is lit for no fuse but my led strip is still being illuminated.
Mike C.
Highly recommend ! This was a great addition to my lead acid to lithium golf cart battery conversion. I added a 48v to 12 reducer and wired into this block to provide 12V to lights, radio, windshield wiper, horn & 12v outlet. Previously 12v's was produced by using 2 of the 6volt batteries. This created uneven drain across the full 8 battery set. This block installed easily, mounted great and has lights to show failed fuse.
Ron B.
IS AT YOUR OWN RISK.
I am rewiring my boat. I decided to have dedicated 12 volt power to my fishing graphs, means clearer images.
Ran new wire from the battery to this fuse panel, wired everything as I needed to, and then notice something.
I am still getting power to the outputs even if there is no fuse in the holder.
Not good.
I wanted to like these and they have great reviews but this is very concerning.
I bought 2 of these and they both do the same thing. That's what I get for going the cheaper route.
I bought 2 of the more expensive one and they both work as they should. Zero power to the outputs.
Good luck.
Marcos A. Garcia
This is the best bang for the buck! Got all my aftermarket accessories organized and professional now. No more cables straight to the battery! The cover is perfectly designed now to pinch the wires! All around great product. It came with extra fuses and label! 5 star product!
paul patterson
I absolutely love this fuse panel. I am going to get a bigger one for my other boat.
Kahlua0619
Good but I would be afraid to run 100 amp through it. This unit is listed to carry 100 amps. Given the tiny studs for the battery cable attachment I would hesitate to run any significant amount of current through it. I ended up removing the tiny cheap studs and replaced them with 1/4" stainless steel bolts. 100 amp battery cables come with 3/8" holes on the terminals and the tiny factory studs didn't seem well suited for them. Even the 1/4 studs seemed rather small. Photo has 1/4" replacement studs on top factory on bottom.
L W. Kaler
Quick shipping. Nice little fuse block perfect for my DIY project.
audie
I bought the 6 circuit fuse block. Great 12 volt distribution box! Well made and came exactly as described. All hardware, labels, fuses and pieces were included as described in the advertisement. There are four predrilled, tapered 3/16" holes in each corner for mounting.
Denis
Works just right, absolutely satisfied
Baboon
Nice small fuse box. Came with fuses and mounting screws which is nice. Didn't use any of the lables. Connecting up was easy and so far working like it should
Max
Works as described - note that the input is from a 48v to 12v converter to run golf car accessories and lighting.
Spiker
Used it to wire up some 12v sockets in the rear of the truck and 4 lights on my contractor cap sides so I can see my parts after sundown and have 12v power at the tailgate. Quality item would buy again. Came with fuses and mounting screws. LED
lights illuminate if a fuse blows showing the circuit that is blown. Very pleased.
Brian
This fuse box does not function as intended. There should be zero volts to a blown or pulled fuse. Disappointed that I spent all that time wiring and it does not work. I will be returning the product. Thumbs down.
Kevin W.
YakutatMan
Simple and straightforward install. My boat is still in winter storage waiting for the snow to melt. I love the easy design and indicator lights if a fuse has blown. It's small enough to mount anywhere. The unit feels solid, has weight to it yet big enough to work with the individual ports. Can't wait to wire this up and hit the water. If any problems I will report back.
Dave C.
When it arrived, it was hard to remove nuts from both terminals, as the bolt would spin with the nut. After using needle nose vice grips, I got it off.
After install and testing. I notice no ground to onboard bus bar. There was connectivity to the terminal but no connection.
So I moved ground wire to bus bar and it worked. It’s not designed to do that, but it’ll do for now. Other than that, it’s working.
Blake wong
It cleans up the battery and wiring. Also, you can remove the fuses in any existing accessories further simplifying your setup.
Korben
This is NOT a fuse block, but a bus terminal.
If you have power flowing through one "fuse" power flows through the rest. I used cheap LEDs to demonstrate this. When one was toggled, the rest would light up dimly. This product is dangerous and WILL kill your circuits. DO NOT BUY IF YOU VALUE YOUR ELECTRONICS.
Customer
This 6 circuit 12 volt fuse holder works great for that but I bought it because the LED red lights in the center are suppose to illuminate when a fuse is blown
Only 2 out of 6 of them do and today only one works. I bought a 2nd unit to replace this broken unit and when I pre tested it, non of the LED lights lite up. I sent a notice to the supplier and he did not respond back. If you buy one of these be sure to at least pre test the lights.
Aaron Archer
Simple fuse block.
Comes with lots of stickers to label the circuits.
Works great
Customer
Installed it on the ergo and now I’m able to run several 12v items on a 48V cart
Landmark Adventures
I used this fuse block to connect branch circuits for three 12VDC devices (so far), each needing less than 5A, to a 15A main circuit in my RV's tech cabinet. Worked perfectly for a neat installation and protects each of those devices with its own 5A fuse.
Mike
Using this as a secondary fuse box for managing electronic accessories on my vehicle, e.g. ditch lights, light pods, auxiliary gauges, etc. Overall, it works great; however, the plastic lid does look quite cheap and isn’t secured particularly well nor sealed. I plan on spray painting it black.
Mudpaco
After about 6 months it still works as intended. No broken top, and no rust. The extra wires are for any future accessories I may add. Very happy with this item.
bmamack
I restore older muscle cars. More specifically I build restro mods. When you take a car that was designed 50-60 years ago, one of the first things that get upgraded is the entire electrical system. Even newer wire harnesses typically don’t have enough inputs and outputs so I always end up using a stand alone module like this one. The overall size makes it easy to fit in tight places, I’ve yet to have any issues with one and for the $, they can’t be beat
Customer
Just got my power Distribution Block and even though i have not used it , it seems very well made for the price my only gripe is the Fuses are as cheap as you can get and doubt they will last long.
Lenny
I am using the unit in the rear of my pickup, mated to a fuse panel, for some LED lights. I also wanted the 12V cigarette lighter as it is heavier than power port. Need a dust buster.
Stan walker
Made a relay board for fog lights on 4x4. Easy to use heavy duty material. Has both + & - battery peg’s which make it much easier. It can run plenty of amp’s threw it. Very highly recommend. O and it does have cover which is not in photo
Slap Nutz
Easy to install and works exactly like it should. Decals could have used a lot less creativity and more straight forward names printed. For instance there is no fuel pump, ignition or fan decals but there is a GPS light decal.
Nice and clean to install, I would buy it again for sure.
Cristian S.
Life saver to say the least. It made everything so easy and simple. Some advice though, if you are using it for a 30amp light bar or any 30amp accessory just buy the fuses at like a nearby auto shop just to be safe (2for 5). It comes with stickers to label everything.
$11.98
View offer